Browse all practice questions for the Massachusetts Journeyman Pipefitter Practice Exam. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Massachusetts Journeyman Pipefitter Practice Exam course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What type of fitting must be installed in the water piping connection at every right angle to assist in cleaning?
  • What is a freezing risk for exterior plumbing components?
  • What is a spirit level primarily used for?
  • What is the maximum connection for a surface blow-down?
  • What part of a high pressure boiler connects the boiler to the discharge system?
  • Which code governs the installation of plumbing systems in Massachusetts?
  • What are the minimum requirements for drainage pipe burial depth?
  • In plumbing, what does 'slope' indicate regarding drain lines?
  • What characterizes a hydronic heating system?
  • Each high-temperature water boiler must have a bottom drain connection of at least how many inches in diameter?
  • What is the minimum thickness for boiler blow-off fittings when the boiler pressure exceeds 100 psig?
  • What is the most common reason for clogs in drain systems?
  • How should you support horizontal runs of piping?
  • What is the function of a valve in a piping system?
  • What is the required cross-sectional area for a discharge pipe used on a safety valve?
  • What is typically the first step before working on a plumbing system?
  • A 3/4" blow-off can be used on high-pressure boilers with less than how many square feet of heating surface?
  • What is the typical application of PEX tubing in plumbing?
  • What is the minimum connection required for something like a water column in plumbing?
  • Which type of material is specified for the minimum size syphon?
  • What is a key precaution when installing underground piping?
  • What does 'leak detection' involve within residential plumbing?
  • Which type of safety relief valve body is prohibited for high-temperature water boilers?
  • Why is it important to use proper sealing compounds on threaded joints?
  • How should joint compounds be applied to threaded pipelines?
  • What does 'vertical rise' mean in piping systems?
  • When a high pressure boiler plant only has one boiler which statement would be true?
  • A syphon is commonly used to protect which device?
  • What is stated regarding mufflers on safety valves in ASME Code?
  • What is the purpose of a vacuum breaker?
  • Which is a common application for CPVC pipes?
  • Which of these practices is essential for preventing tool damage?
  • In the heating boiler code, where should an additional stop valve be placed when one is used in the supply pipe connection?
  • What item is not commonly used when piping up a reducing station?
  • What is the function of a thermostatic mixing valve?
  • What is a sign of effective drainage capacity?
  • Explain the role of hydronic heating in building comfort systems.
  • What is the minimum pipe size in inches required for the water column drain cock or drain valve?
  • What is a common maximum connection size for threaded safety valves?
  • Which component is key in preventing backflow in plumbing systems?
  • What is the maximum temperature limitation for non-ferrous pipe attached directly to a boiler?
  • What is the minimum vent size for residential plumbing systems in Massachusetts?
  • Which valve offers the least resistance to flow?
  • Which of the following materials is commonly used in plumbing systems?
  • What process should be conducted when pressure testing a piping system?
  • At all high points of a chilled water system, what should be installed?
  • What is the most appropriate valve application for a surface blow-off system?
  • What is the purpose of a pressure relief valve?
  • How far should vent pipes be located from windows in a residential setting?
  • What is the minimum size of the drain pipe required on a low water cut-off with a separate float chamber?
  • Why is proper pipe sizing significant in plumbing systems?
  • What cast iron item is not allowed on a high pressure boiler?
  • How can one extend the lifespan of plumbing tools?
  • For safety, how many means of water feed are required when exceeding 500 square feet of heating surface?
  • What size piping connection requires consideration for adjustable hangers?
  • What does ensuring proper depth in underground piping help avoid?
  • Under what conditions can the size of bottom blow-down lines be reduced?
  • The automatic non-return valve on a high pressure boiler is located ________________ .
  • Which type of pipe is commonly used for gas lines?
  • What is the maximum connection size for a threaded safety valve?
  • Which device triggers a safety shut-down requiring a manual reset?
  • Hangers used for the support of piping, NPS how many inches and larger, shall be designed to permit adjustment after erection?
  • Safety valve or safety relief valve discharges shall be located or piped in what manner?
  • What is the maximum PSI for malleable iron?
  • At what minimum size must a syphon be made of non-ferrous material?
  • What is a common application for a 90-degree elbow fitting?
  • At what temperature do safety plugs on an acetylene bottle melt?
  • What does the term 'slope' refer to in drainage systems?
  • What is the primary purpose of a pipefitting system in construction?
  • What is the minimum connection size for a sight glass?
  • How high must low water fuel cut-off devices be piped in relation to the gauge glass?
  • What is a double sanitary tee used for?
  • Where is the required boiler feed water stop valve located on a high-pressure boiler?
  • The purpose of a Flash Tank is to _____________________ .
  • What safety protocol should be followed when soldering copper pipes?
  • Cast iron pipe can be used to carry steam at pressures up to what pressure (psig)?
  • What is the minimum size connection for a sight glass drain?
  • When caring for plumbing tools, what is NOT recommended?
  • Over what pressure is it required to have two sight glasses?
  • What is a true statement regarding a boiler water column?
  • What should be prioritized to ensure effective piping installation?
  • What are the advantages of using PEX tubing?
  • The Bourdon Tube of a steam pressure gauge _______________ .
  • What should be routinely checked to ensure the functionality of high pressure boiler systems?
  • What is the minimum connection required for a low water cut-off draw?
  • What is water hammer?
  • What is an abrasive saw commonly referred to as?
  • What should be avoided when installing underground piping?
  • Why is cross-connection control important in plumbing?
  • What is the primary material composition of CPVC pipes?
  • Which material is crucial to consider when installing underground piping?
  • What is the function of air admittance valves (AAVs)?
  • What does the blow-off valve's discharge outlet need to ensure?
  • At what temperature do brazing joints typically melt?
  • Which of the following valves would be least effective in a blow-off application?
  • What is the largest safety valve that may be attached to a steam drum of a high pressure boiler by threading?
  • What connection is associated with an ASME code stamp for high-pressure main steam lines?
  • What is the minimum pipe size for all gauge glass connections?
  • What is the role of a thermostat in hydronic heating systems?
  • What is the purpose of a cleanout in a piping system?
  • What is a method to prevent sharp bends in piping?
  • What does the term 'drainage capacity' refer to?
  • What is the primary function of a check valve in plumbing?
  • What is the primary purpose of an auxiliary low-water cut-off device?
  • How is the slope for drainage pipes typically calculated?
  • What is the maximum size limitation for ANSI class 600 socket welded flanges in boiler external piping?
  • What is the minimum connection size for a control line take-off?
  • The maximum size of a surface blow-off connection shall not exceed how many inches?
  • How does a union differ from a coupling in pipefitting?
  • What is the maximum allowable size for slip-on flanges used in boiler external piping according to ASME B.31.1?
  • Which type of valve is used to control flow in a piping system?
  • What is the purpose of a check valve?
  • Where does the bottom blow down line of a high pressure water tube boiler connect?
  • What is a common material used for vent pipes?
  • What is a key benefit of using solvent cement for joining pipes?
  • Why is it necessary to maintain the slope in drainage pipes?
  • The minimum pressure rating for all valves on a heating boiler should equal which of the following?
  • What is the main purpose of a plumbing trap?
  • What does 'drainage' entail in a piping system?
  • What type of maintenance can lead to tool deterioration?
  • What is the maximum suggested pipe support spacing for 6" pipe used for steam, gas, or air service?
  • What is the minimum connection size for a control manifold?
  • What is the primary function of a safety valve on a high pressure boiler?
  • What is the purpose of a trap in plumbing systems?
  • The steam and water connections to a water column or water gauge glass on a high pressure boiler must be accessible for what purpose?
  • According to the ASME high pressure boiler code, a boiler that has more than how many square feet of heating surface must have 2 or more safety valves?
  • An altitude gauge is required on a hot water supply boiler at altitudes over how many feet?
  • What is the typical life expectancy of copper piping?
  • When two or more high-pressure boilers are connected to a common steam header, what is required for each boiler?
  • An altitude gauge is necessary for systems located at higher altitudes due to what reason?
  • Boiler blow-down tanks are classified as what type of piping?
  • What is the maximum allowable distance from a fixture to a trap according to plumbing code?
  • How are PVC pipes typically joined?
  • What is the minimum connection size for a bottom blow-off?
  • What is the primary purpose of using rigid support for pipes over long vertical runs?
  • What is the allowable maximum PSI for a piping system made of ASTM C-857?
  • What is the role of a trap in a plumbing system?
  • What is the minimum pipe size that requires hangers to be adjusted over?
  • What connection size is needed for a water column?
  • According to ASME B31.1, what material should boiler blow-off fittings be made from when boiler pressure exceeds 100 psig?
  • The main purpose of a safety valve is to what?
  • What is the standard maximum size for a take-off in a control line?
  • What type of hazard does improper pipe installation or design create?
  • For steam service, what type of joint is preferable on a high pressure boiler?
  • What is the minimum connection for a sight glass drain?
  • What is the maximum size for a socket welded fitting?
  • What is an acceptable use of dielectrics in plumbing?
  • What is the purpose of using hangers in piping systems?
  • What material is commonly used for piping insulation?
  • What is the minimum pressure rating required for valves and fittings on steam lines for high-pressure boilers?
  • Which type of connector is commonly used for joining copper pipes?
  • When installing a low water cut-off on a hot water heating boiler, you may install it ____________________ .
  • What is commonly used to seal connections in PVC piping systems?
  • How many stop valves are required between boilers having a manhole opening when connected to a common steam header?
  • Which valve is not appropriate as a boiler steam outlet valve on a high pressure boiler?
  • What is the maximum connection for a flanged safety valve?
  • What is a 'dead leg' in a piping layout?
  • What is the minimum BTU input that requires a Massachusetts pipefitting license for heating systems?
  • For a single boiler installation, where is an ASME code stamp required?
  • When more than 2 high pressure safety valves of different sizes are mounted on a boiler, the relieving capacity of the smaller valve should not be less than what percentage of that of the larger valve?
  • In piping terminology, what is a 'reducer'?
  • The ability of a drainage system to avoid clogging is known as?
  • Which form of safety valve mounting is prohibited in the heating boiler code?
  • In plumbing terminology, what does 'vent stack' refer to?
  • How can water hammer be prevented?
  • The discharge pipe of a high pressure safety valve should be configured in what manner?
  • Why is it important to pressure test a completed piping installation?
  • The Bourdon Tube in a steam pressure gauge is protected by a ________________ .
  • What does 'backflow' refer to in plumbing systems?
  • What is required on a hot water boiler when the boiler pressure exceeds 30 psig?
  • What is the appropriate valve application for a boiler blow-off valve on a high-pressure boiler?
  • What considerations must be made when installing a sump pump?
  • For high pressure boilers with more than 100 square feet of heating surface, the feed connection shall not be smaller than which pipe size?
  • What is an important maintenance practice for plumbing tools?
  • What diameter of pipe is required for the bottom drain connection of high-temperature water boilers?
  • The discharge outlet of a safety valve must not be what?
  • What is a common feature of modern plumbing systems to manage water flow?
  • What tool is commonly used to cut copper pipe?
  • Under what condition shall mufflers not be used on safety relief valves according to ASME Code?
  • The minimum temperature rating of all valves or cocks on a heating boiler should be at least what degree Fahrenheit?
  • The pipe sizes required for the boiler equalizer line are based on what capacity?
  • A slow-opening valve requires how many complete turns to be fully opened or closed?
  • According to ASME code, what is the minimum size of pipes connecting the water column to a boiler?
  • When must two or more safety valves be used on a steam heating boiler?
  • What is a result of poor drainage capacity in a system?
  • What is the function of a pressure gauge in a piping system?
  • What material must the boiler blow-off fittings be when the pressure exceeds 100 psi?
  • What is the recommended maximum length for vent piping?
  • What is the primary function of a 'trap' in a plumbing system?
  • Which is mandatory to have installed on a separate connection on a hot water heating boiler?
  • What is the minimum connection size for safety-related plumbing equipment?
  • What is the maximum connection size for a bottom blow-off?
  • What is the primary function of hangers in piping systems?
  • The connection between a boiler and the safety valve must be at least what size?
  • At what pressure is an ASME Section VIII expansion tank required on a hot water boiler?
  • What is the maximum water temperature for heating boilers according to ASME V?
  • The pipefitter license is governed by Chapter 146 of M.G.L. The section of this law is section _________ of the M.G.L.
  • What does 'drainage fixture unit' (DFU) refer to?
  • What does the acronym 'NFPA' stand for?
  • For a control manifold, what is the required minimum connection size?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy